>@SYSGEN
>;
>; RSX-11M-PLUS V4.6 BL87 SYSGEN
>;
>; Copyright (c) 1995-1999 by Mentec Inc., U.S.A.
>;
>SET /DPRO=[RWED,RWED,RWE,R]
>;
>; To exit from the SYSGEN procedure at any time, type CTRL/Z.
>;
>; If you are unsure of the answer to a question for which a de-
>; fault answer exists, use the default answer.
>;
>;
>;
>;===================================================
>; Choosing SYSGEN Options 19-OCT-08 at 15:41
>;===================================================
>;
>;
>;
>; Every question is preceded by a question number (for example SU010)
>; which you can use to find the explanation of the question in the
>; RSX-11M-PLUS System Generation and Installation Guide.
>;
>; An explanation of every question is also available by pressing
>; the ESC key (or the ALTMODE key) in response to the question.
>;
>; If you are unfamiliar with the SYSGEN procedure, the explanation of
>; each question can be printed automatically before the question.
>;
>* SU010 Do you always want the explanation printed? [Y/N D:N]: Y
>;
>; SYSGEN always creates saved answer files containing your responses
>; to the SYSGEN questions:
>;
>; SYSGENSA1.CMD Setup questions, Executive options
>; SYSGENSA2.CMD Peripheral configuration
>; SYSGENSA3.CMD Nonprivileged task builds
>;
>; You should perform a PREPGEN first to create saved answer files, and
>; then perform a SYSGEN, specifying those saved answer files as input
>; to the Executive, peripheral, and nonprivileged task build sections.
>;
>; If you have performed a SYSGEN (or PREPGEN) before, you can use the
>; saved answer file created during that SYSGEN as input to this SYSGEN.
>; SYSGEN uses the saved answers as your responses to the Executive
>; questions.
>;
>* SU020 Do you want to use a saved answer file as input for
>* the Executive options? [Y/N D:N]:
>;
>* SU040 Do you want to use a saved answer file as input for
>* the peripheral configuration? [Y/N D:N]:
>;
>* SU060 Do you want to use a saved answer file as input for
>* the nonprivileged task builds? [Y/N D:N]:
>;
>; A PREPGEN allows you to answer all the SYSGEN questions and create
>; saved answer files without actually generating a system: no MCR
>; commands are executed, no files are deleted, and the Executive is
>; not assembled or built.
>;
>; After you have successfully completed a PREPGEN, you can perform a
>; SYSGEN using the saved answer files from the PREPGEN. The SYSGEN
>; will then run unattended.
>;
>* SU080 Do you want to do a PREPGEN? [Y/N D:N]:
>;
>; You should have a disk spinning in a disk drive which is a copy of
>; your distribution kit. This is your target system disk, the disk on
>; which you will perform the SYSGEN. This disk should already be
>; mounted with the MOUNT command so that you have access to it.
>;
>; Enter the name of the drive containing this disk in the form ddnn:,
>; i.e., DB2:.
>;
>* SU090 Enter the name of the disk drive containing your
>* target system disk [ddnn:] [S R:2-5]: DU:
>;
>ASN DU:=IN:
>ASN DU:=OU:
>ASN DU:=LB:
>ASN DU:=WK:
>ASN DU:=TK:
>ASN DU:=BC:
>ASN DU:=LI:
>ASN DU:=OB:
>ASN DU:=EX:
>ASN DU:=MP:
>;
>; You can:
>;
>; o do a complete SYSGEN
>;
>; o continue a previous SYSGEN from where you left off
>;
>; o do an individual section of SYSGEN
>;
>;
>; A complete SYSGEN consists of:
>;
>; Choosing Executive options
>; Choosing Peripheral Configuration
>;
>; Assembling the Executive and Drivers
>;
>; Building the Executive and Drivers
>; Building the Privileged Tasks
>; Building the Nonprivileged Tasks
>;
>; Creating the System Image File
>;
>; If you do not choose to do a complete SYSGEN, you can continue
>; a previous SYSGEN from where you left off or do an individual
>; section of SYSGEN.
>;
>* SU120 Do you want to do a complete SYSGEN? [Y/N D:Y]:
>;
>INS [3,54]MAC/TASK=MACT0
>INS [3,54]PIP/TASK=PIPT0
>INS [3,54]LBR/TASK=LBRT0
>INS [3,54]TKB/TASK=TKBT0
>INS [3,54]VMR/TASK=VMRT0
>;
>;
>;
>;======================================================
>; Choosing Executive Options 19-OCT-08 at 15:41
>;======================================================
>;
>;
>;
>; The answers to the questions in this section are put in the saved
>; answer file [200,200]SYSGENSA1.CMD.
>;
>; You may now enter a comment describing the system you are building.
>; This comment is included in the SYSGENSA1 saved answer file for
>; documentation, and is printed out when the saved answer file is
>; later used as input.
>;
>; Enter a comment for inclusion in the SYSGENSA1 saved answer file.
>; The comment may contain more than one line. The "V" in the right
>; margin below marks the maximum line length. When you are done,
>; press RETURN in response to the prompt.
>; V
>* Comment [S R:0.-55.]:
>;
>; RSX-11M-PLUS may be run on the following PDP-11 processors:
>;
>; 11/23-PLUS (also called MicroPDP-11/23 and 11/23-B)
>; 11/24
>; 11/44
>; 11/53
>; 11/70
>; 11/73 (also called MicroPDP-11/73)
>; 11/83 (also called MicroPDP-11/83)
>; 11/93 (also called MicroPDP-11/93)
>; 11/84
>; 11/94
>;
>; M70,80,90,100 MENTEC modules (treated as an 11/83)
>; M11 processor (MENTEC)
>;
>; LSI-11/73
>;
>* CE010 What is your target processor type? [S R:3.-12. D:"11/70"]: 11/93
>;
>; The following RSX-11M-PLUS Executives may be generated:
>;
>; o Full-functionality Executive
>;
>; o User-tailored Executive
>;
>;
>; The Full-functionality Executive includes all features of the
>; RSX-11M-PLUS operating system that can be used on your processor.
>;
>; Executive data space support
>; User data space support
>; Task headers out of pool support
>; Extended logical name support
>; Supervisor-mode library support
>; Fast map facility
>; All DIGITAL-supplied drivers are loadable
>; ICB pool size of 128. words
>; Shadow recording/load sharing support
>; Floating point processor (FPU) support
>; Disk data caching support
>; Console driver support
>; Accounting support
>; Batch processor support
>; Queue Manager for spooling
>; DIGITAL Command Language and alternate CLI support
>; CTRL/C abort support
>; Extended security support
>; Alternate checkpoint algorithm support
>; High performance FCP
>; File windows in secondary pool support
>; Decimal version numbers in file specifications
>; Virtual terminal support with a default virtual terminal
>; unit buffer size of 120. bytes and a maximum of 184. bytes
>; Character translation support
>; Terminal driver extended I/O support
>; Time-out on unsolicited terminal input of 30. seconds
>;
>;
>; The User-tailored Executive will require you to answer at least
>; twenty additional questions specifying which standard RSX-11M-PLUS
>; features you wish to disable. You should not choose the User-tailored
>; Executive unless you need to disable specific RSX-11M-PLUS features.
>;
>;
>; For information and guidelines on generating a User-tailored Executive,
>; please refer to the RSX-11M-PLUS System Generation and Installation
>; Guide.
>;
>; If you do not understand the options presented by the system
>; generation process when configuring an Executive yourself, please
>; select the Full-functionality Executive.
>;
>;
>* CE020 Do you want the Full-functionality Executive? [Y/N D:Y]:
>;
>; If a primary pool failure occurs, this option will allow the
>; the system to utilize ICB pool space as a secondary source to
>; be able to attempt to resolve the pool allocation failure.
>;
>; Some applications may have to be aware of this possibility, or
>; undefined results may occur. All supported software products
>; are aware of this change, and do function correctly if this option
>; is chosen.
>;
>* CE115 Do you want to use ICB pool as backup for primary pool ? [Y/N D:N]: Y
>;
>; Network software provides the capability of simultaneously
>; operating tasks on different systems to establish logical
>; communication links and to exchange data. This software is
>; not provided with RSX-11M-PLUS, but must be purchased separately.
>;
>; If you choose this option, DCL and alternate CLI support will
>; also be included.
>;
>* CE120 Do you want support for communications products
>* (such as DECnet, PSI, and LAT)? [Y/N D:N]: Y
>;
>; The system name is an arbitrary six-character name.
>; This should be the same as the DECnet node name, if any.
>;
>* CE130 What is the system name? [S R:0-6 D:"RSXMPL"]: BOPOHA
>;
>; This option determines if dates should be displayed according to
>; ISO 8601 format specification.
>;
>; For example; if the date February 1, 2000 should be displayed
>; as 2000-02-01
>;
>;
>* CE215 Do you want the default date format to be
>* ISO 8601:1988 compliant? [Y/N D:N]:
>;
>; This option determines if dates should be displayed as two or four
>; digits. For example; if the year January 1, 2000 should be displayed
>; as 1-JAN-00, or 1-JAN-2000.
>;
>; If you specify Yes, the default date format will be;
>;
>; 1-JAN-2000,
>;
>; otherwise the default date format will be;
>;
>; 1-JAN-00
>;
>* CE216 Do you want the default date format to include
>* a four digit year? [Y/N D:N]:
>;
>; The IP11 industrial I/O subsystem is a combined software and
>; hardware package used for process control and monitoring in
>; the industrial and manufacturing environment. It consists
>; of an RSX device driver (IPDRV) and a set of FORTRAN-callable
>; interface routines, used to interface to a variety of hardware
>; I/O modules, including digital sense interrupt, change-of-state,
>; digital output, digital-to-analog converter, and analog-to-digital
>; converter modules.
>;
>; See the IP11 I/O Subsystem Software Installation Guide for
>; information on installing the software.
>;
>* CE264 Do you want IP11 industrial I/O subsystem support? [Y/N D:N]:
>;
>; The Executive Debugging Tool (XDT) provides a subset of ODT-11
>; that runs as a part of the RSX-11M-PLUS Executive. This tool
>; allows interactive debugging of Executive modules, I/O drivers,
>; and interrupt service routines. Selection of this option also
>; includes consistency checks in the dynamic memory routines and
>; the loader.
>;
>; Note: If your system does not have Executive data space support,
>; XDT will reduce the size of primary pool. If your system does
>; have Executive data space support, XDT does not affect the size
>; of pool.
>;
>* CE270 Do you want to include XDT? [Y/N D:N]: Y
>;
>; If the system crashes, a message is printed on the crash
>; notification device. This device must be a paper tape,
>; teletype, or line printer compatible device; that is, the
>; device must transmit a single byte at a time. Normally,
>; the crash notification device is the console terminal which
>; is always at the default CSR address given below.
>;
>* CE280 Enter the crash notification device CSR
>* address [O R:160000-177700 D:177564]:
>;
>; If the system crashes, you can cause all of memory to be written
>; onto a device for later analysis with the Crash Dump Analyzer (CDA).
>;
>; The device on which the crash dump is written must be selected from
>; the following list of devices and cannot be a fixed media device:
>;
>; DB: DM: MM:
>; DD: DR: MS:
>; DK: DT: MT:
>; DL: DU: MU:
>;
>; Note: Enter both the device and the logical unit number.
>; For example, MM0: or DL1:.
>;
>; Note: Enter XX: if you desire loadable DU:, DL:, MU:, MS: or MM:
>; crash driver support.
>;
>* CE290 On what device and unit do you want crash dumps
>* to be written? [S R:2-6]: XX:
>;
>; Virtual disks allow the system to better manage large amounts
>; of storage. If you expect to hardware of software boot virtual
>; drives, select the maximum depth of virtual devices which will
>; be booted.
>;
>* CE300 Enter the initial number of virtual disks to be
>* included [D R:0.-16. D:2.]: 1
>;
>; The minimum supported memory size is 256K words for
>; an RSX-11M-PLUS system. The maximum memory size is 2044K words.
>;
>; This value is only used by VMR when it creates the system image
>; file. VMR does not allow you to create a partition or load
>; anything beyond the end of memory. When the system is booted,
>; your actual memory size is calculated and overrides the value
>; you enter here.
>;
>* CE310 Enter memory size (in K words) [D R:256.-2044. D:256.]:
>;
>; Some PDP-11/44 and PDP-11/84 systems are configured with UNIBUS
>; memory which disables some UNIBUS Map registers. If support for
>; UNIBUS memory is selected, then special UNIBUS memory partitons
>; are supported, and specific UMR resources reserved when UNIBUS
>; memory is detected on the system. If your system does not contain
>; any memory devices on the UNIBUS, this option will have no effect.
>;
>* CE315 Support UNIBUS memory occupying UNIBUS map address space? [Y/N D:N]:
>;
>; RSX-11M-PLUS requires a real-time clock for its operation. The
>; KW11-P programmable frequency clock, the KW11-L line frequency
>; clock, or the DL11-W line frequency clock/console interface may
>; be used.
>;
>* CE330 Is your system clock programmable (KW11-P)? [Y/N D:N]:
>;
>; Line frequency is either 50 or 60 Hz. In the U.S.A., line frequency
>; is always 60 Hz.
>;
>* CE350 Is your line frequency 50 Hz? [Y/N D:N]: Y
>;
>;
>;
>;=============================================================
>; Choosing Peripheral Configuration 19-OCT-08 at 15:42
>;=============================================================
>;
>;
>;
>; The answers to the questions in this section are put in the saved
>; answer file [200,200]SYSGENSA2.CMD.
>;
>; You may now enter a comment describing the system you are building.
>; This comment is included in the SYSGENSA2 saved answer file for
>; documentation, and is printed out when the saved answer file is
>; later used as input.
>;
>; Enter a comment for inclusion in the SYSGENSA2 saved answer file.
>; The comment may contain more than one line. The "V" in the right
>; margin below marks the maximum line length. When you are done,
>; press RETURN in response to the prompt.
>; V
>* Comment [S R:0.-55.]:
>;
>;
>; The RH11 and RH70 MASSBUS controllers are the controllers for
>; the following devices:
>;
>; DB: RP04, RP05, RP06, RM06 disks
>; DR: RM02, RM03, RM05, RM06, RM80, RP07 disks
>; DS: RS03, RS04 disks
>; EM: ML11 semiconductor disk emulator
>; MM: TM02, TM03 formatters, TE16, TU16, TU45, TU77 tapes
>;
>* CP0604 How many RH controllers do you have? [D R:0.-15. D:4.]:
>;
>; A mixed MASSBUS configuration has different device types on the
>; same RH controller. For example, a DB type disk and a DR type disk
>; both connected to RHA. Having an RP04 and an RP06 (both DB type
>; disks) connected to the same controller is NOT a mixed MASSBUS
>; configuration.
>;
>; If you choose to generate a mixed MASSBUS configuration, all the
>; MASSBUS device data bases will be resident.
>;
>* CP0612 Do you want to generate a mixed MASSBUS configuration? [Y/N D:N]:
>;
>;
>; DB: controllers: RH11, RH70 devices: RP04, RP05, RP06, RM06
>;
>; The RP04/05/06 are 19 data surface, removable, random access
>; bulk storage systems with storage capacities of 88 megabytes
>; (RP04/05) and 176 megabytes (RP06) per pack. The RM06 is the
>; SETASI Shelby replacement drive for RM/RP drives.
>;
>* CP0808 How many RP04/05/06 disk drives do you have? [D R:0.-63. D:0.]: 8
>;
>; A dual-access unit is one that is connected to two controllers
>; at one time, and may be accessed from either controller at the
>; option of the system software. Since a single device unit may
>; have only one physical unit number, a dual-access unit must be
>; attached to both controllers with the same unit number.
>;
>* CP0820 Are any of the units dual-access? [Y/N D:N]:
>;
>;
>; The physical unit number of a drive is the number shown on the
>; unit number plug (or other indicator) on the drive.
>;
>* CP0836 What is the physical unit number of DB0:? [O R:0-7 D:0]:
>;
>; The legal characters in a controller specification are:
>;
>; A thru D
>;
>; Where the DEC alphabet is: A,B,C,D,E,F,H,J,K,L,M,N,P,R,S,T
>; Note that the letters G, I, O, and Q are omitted for clarity.
>;
>* CP0844 To which RH controller is DB0: connected? [S R:1-1]: A
>;
>; Enter the drive type for this logical unit.
>;
>; Note: As far as SYSGEN is concerned, there is no difference between
>; an RP04 and an RP05 drive.
>;
>* CP0860 Is DB0: an RP04, RP05, RP06, or RM06? [S R:4-4 D:"RP06"]:
>;
>;
>* CP0836 What is the physical unit number of DB1:? [O R:0-7 D:1]:
>;
>* CP0844 To which RH controller is DB1: connected? [S R:1-1]: A
>;
>* CP0860 Is DB1: an RP04, RP05, RP06, or RM06? [S R:4-4 D:"RP06"]:
>;
>;
>* CP0836 What is the physical unit number of DB2:? [O R:0-7 D:2]:
>;
>* CP0844 To which RH controller is DB2: connected? [S R:1-1]: A
>;
>* CP0860 Is DB2: an RP04, RP05, RP06, or RM06? [S R:4-4 D:"RP06"]:
>;
>;
>* CP0836 What is the physical unit number of DB3:? [O R:0-7 D:3]:
>;
>* CP0844 To which RH controller is DB3: connected? [S R:1-1]: A
>;
>* CP0860 Is DB3: an RP04, RP05, RP06, or RM06? [S R:4-4 D:"RP06"]:
>;
>;
>* CP0836 What is the physical unit number of DB4:? [O R:0-7 D:4]:
>;
>* CP0844 To which RH controller is DB4: connected? [S R:1-1]: A
>;
>* CP0860 Is DB4: an RP04, RP05, RP06, or RM06? [S R:4-4 D:"RP06"]:
>;
>;
>* CP0836 What is the physical unit number of DB5:? [O R:0-7 D:5]:
>;
>* CP0844 To which RH controller is DB5: connected? [S R:1-1]: A
>;
>* CP0860 Is DB5: an RP04, RP05, RP06, or RM06? [S R:4-4 D:"RP06"]:
>;
>;
>* CP0836 What is the physical unit number of DB6:? [O R:0-7 D:6]:
>;
>* CP0844 To which RH controller is DB6: connected? [S R:1-1]: A
>;
>* CP0860 Is DB6: an RP04, RP05, RP06, or RM06? [S R:4-4 D:"RP06"]:
>;
>;
>* CP0836 What is the physical unit number of DB7:? [O R:0-7 D:7]:
>;
>* CP0844 To which RH controller is DB7: connected? [S R:1-1]: A
>;
>* CP0860 Is DB7: an RP04, RP05, RP06, or RM06? [S R:4-4 D:"RP06"]:
>;
>;
>; DR: controllers: RH11, RH70 devices: RM02, RM06
>; RH70 RM03, RM05, RM06, RM80, RP07
>;
>; The RM02/03/05 are removable pack, random access disk storage
>; systems with a storage capacity of 67 megabytes (RM02/03) and
>; 256 megabytes (RM05) per pack.
>;
>; The RM80 and RP07 are fixed media, random access disk storage
>; systems with a storage capacity of 124 megabytes (RM80) and
>; 516 megabytes (RP07) per pack.
>;
>; The RM06 is a SETASI drive with a massbus ID using 47, which is
>; autosizeable when the drive is brought online. This option should
>; only be selected when not using a personality diskette for another
>; type of RM device.
>;
>* CP1008 How many RM02/03/05/06/80/RP07 disk drives do you
>* have? [D R:0.-63. D:0.]:
>;
>;
>; DS: controllers: RH11, RH70 devices: RS03, RS04
>;
>; The RS03/04 are small, fast, fixed-media disks. The RS03 has a
>; capacity of 256K words. The RS04 has a capacity of 512K words.
>; The transfer rate is 4 microseconds per word with an average latency
>; of 8 milliseconds.
>;
>* CP1208 How many RS03/04 disk drives do you have? [D R:0.-63. D:0.]:
>;
>;
>; EM: controllers: RH11, RH70 device: ML11
>;
>; The ML11 is a fast, random access, block mode MOS memory system.
>; The ML11-A (16K chips) provides up to 4 megabytes of storage.
>; The ML11-B (64K chips) provides up to 16 megabytes of storage.
>;
>* CP1408 How many ML11 disks do you have? [D R:0.-63. D:0.]:
>;
>;
>; MM: controllers: RH11, RH70 devices: TE16, TU16, TU45, TU77
>; formatters: TM02, TM03
>;
>; The TU16/45/77/TE16 magnetic tape drive unit is ideally suited
>; for writing, reading, and storing large volumes of data and
>; programs in a serial manner. The 10 1/2-inch tape reels
>; contain up to 2400 feet of tape. The tape is 9-track, recorded
>; either NRZI or phase encoded with recording densities of 800 or
>; 1600 bpi.
>;
>* CP1608 How many TU16/45/77/TE16 tape drives do you
>* have? [D R:0.-256. D:0.]: 1
>;
>; Each TU16/45/77/TE16 drive unit is interfaced to the RH MASSBUS
>; controller through a TM02/03 magtape formatter. A single formatter
>; is connected to the MASSBUS as one physical unit, and in turn will
>; support up to eight drives.
>;
>; The formatter and the first drive interfaced to it are called
>; the "master drive" unit. Any additional drives on the formatter
>; are called "slave drive" units.
>;
>; The TM02/03 formatter is usually located behind the lower front
>; door of the master drive. It has a white physical unit number plug
>; inserted into it. (Do not confuse it with the power supply.)
>;
>* CP1612 How many TM02/03 magtape formatters do you
>* have? [D R:1.-1. D:1.]:
>;
>;
>; The physical unit number of a formatter is the physical unit
>; number by which it is attached to the MASSBUS. This number is NOT
>; determined by the easily visible white unit number plug (or other
>; indicator) on the tape transport. Instead it must be determined
>; from the formatter itself. The TM02/03 formatter is usually
>; located behind the lower front door of the master drive. (Do not
>; confuse it with the power supply.) Its physical unit number is
>; determined by the white unit number plug inserted into it.
>;
>* CP1636 What is the physical unit number of the next
>* formatter? [O R:0-7 D:0]:
>;
>; The legal characters in a controller specification are:
>;
>; A thru D
>;
>; Where the DEC alphabet is: A,B,C,D,E,F,H,J,K,L,M,N,P,R,S,T
>; Note that the letters G, I, O, and Q are omitted for clarity.
>;
>* CP1644 To which RH controller is this formatter connected? [S R:1-1]: C
>;
>; The 1. remaining tape drive(s) will be allocated to this formatter.
>;
>;
>; The physical unit number of a tape drive is the physical unit number
>; by which it is attached to its formatter. This number is determined
>; by the easily visible white unit number plug (or other indicator) on
>; the tape drive.
>;
>; If you have eight or fewer tape drives, we suggest, for convenience,
>; that you make the physical unit numbers match the logical unit
>; numbers.
>;
>; Warning: Only four TU77s are allowed on a formatter. Therefore,
>; TU77s cannot have physical unit numbers greater than 3. SYSGEN
>; cannot tell if you have TU77s and so will not catch the error if
>; you specify physical unit numbers greater than 3 for TU77s. Those
>; tape drives will not be useable in the resulting system.
>;
>* CP1656 What is the physical unit number of MM0:? [O R:0-7 D:0]:
>;
>;
>; Enter the vector address for this controller. This vector address
>; can be changed after the SYSGEN by using the VMR CON SET command.
>;
>* CP2068 Enter the vector address of RHA [O R:60-774 D:254]:
>;
>; Enter the CSR address for this controller. This CSR address can
>; be changed after the SYSGEN by using the VMR CON SET command.
>;
>* CP2072 What is its CSR address? [O R:160000-177700 D:176700]:
>;
>; SGN -- Warning: Controller RHB has no units attached to it.
>;
>;
>;
>; Enter the vector address for this controller. This vector address
>; can be changed after the SYSGEN by using the VMR CON SET command.
>;
>* CP2068 Enter the vector address of RHC [O R:60-774 D:224]:
>;
>; Enter the CSR address for this controller. This CSR address can
>; be changed after the SYSGEN by using the VMR CON SET command.
>;
>* CP2072 What is its CSR address? [O R:160000-177700 D:172440]:
>;
>; SGN -- Warning: Controller RHD has no units attached to it.
>;
>;
>; RH Configuration
>;
>; Physical Unit Number
>;
>; 0 1 2 3 4 5 6 7
>;
>; RHA DB0: DB1: DB2: DB3: DB4: DB5: DB6: DB7:
>; RHB
>; RHC MM0:
>; RHD
>;
>;
>; MM Master / Slave Configuration
>;
>; Master Slave Units
>;
>; MM0:
>;
>;
>;
>;
>; DK: controller: RK11 devices: RK05, RK05F
>;
>; The RK11 cartridge disk drive and control is a complete mass
>; storage system for random access data storage. The system
>; includes a modular mass storage device utilizing removable
>; disk cartridges and a complete, easy-to-program, control unit.
>; A disk cartridge holds over 2.4 megabytes. The system is
>; expandable up to 8 drives per controller. An RK11 includes a
>; controller and the first disk drive. Optionally, the controller
>; can support up to four RK05F fixed platter drives each with twice
>; the capacity of the standard RK05 drive.
>;
>* CP2204 How many RK11 cartridge disk controllers do you have? [O D:0]:
>;
>;
>; DM: controllers: RK611, RK711 devices: RK06, RK07
>;
>; The RK611/711 is a 3 data surface, removable, random access bulk
>; storage system with a storage capacity of 14 megabytes (RK06) or
>; 28 megabytes (RK07) per pack. The RK611/711 includes a control
>; unit and the first disk pack drive. The system is expandable up
>; to eight drives.
>;
>* CP2404 How many RK611/711 disk cartridge controllers do
>* you have? [O D:0]: 1
>;
>; Enter the total number of RK06 and RK07 disk drives in your system.
>;
>* CP2408 How many RK06/RK07 disk drives do you have? [D R:1.-63. D:1.]: 8
>;
>;
>; The physical unit number of a drive is the number shown on the
>; unit number plug (or other indicator) on the drive.
>;
>* CP2436 What is the physical unit number of DM0:? [O R:0-7 D:0]:
>;
>; Enter the drive type for this logical unit.
>;
>* CP2460 Is DM0: an RK06 or RK07? [S R:4-4 D:"RK07"]:
>;
>;
>* CP2436 What is the physical unit number of DM1:? [O R:0-7 D:1]:
>;
>* CP2460 Is DM1: an RK06 or RK07? [S R:4-4 D:"RK07"]:
>;
>;
>* CP2436 What is the physical unit number of DM2:? [O R:0-7 D:2]:
>;
>* CP2460 Is DM2: an RK06 or RK07? [S R:4-4 D:"RK07"]:
>;
>;
>* CP2436 What is the physical unit number of DM3:? [O R:0-7 D:3]:
>;
>* CP2460 Is DM3: an RK06 or RK07? [S R:4-4 D:"RK07"]:
>;
>;
>* CP2436 What is the physical unit number of DM4:? [O R:0-7 D:4]:
>;
>* CP2460 Is DM4: an RK06 or RK07? [S R:4-4 D:"RK07"]:
>;
>;
>* CP2436 What is the physical unit number of DM5:? [O R:0-7 D:5]:
>;
>* CP2460 Is DM5: an RK06 or RK07? [S R:4-4 D:"RK07"]:
>;
>;
>* CP2436 What is the physical unit number of DM6:? [O R:0-7 D:6]:
>;
>* CP2460 Is DM6: an RK06 or RK07? [S R:4-4 D:"RK07"]:
>;
>;
>* CP2436 What is the physical unit number of DM7:? [O R:0-7 D:7]:
>;
>* CP2460 Is DM7: an RK06 or RK07? [S R:4-4 D:"RK07"]:
>;
>;
>; Enter the vector address for this controller. This vector address
>; can be changed after the SYSGEN by using the VMR CON SET command.
>;
>* CP2468 Enter the vector address of DMA [O R:60-774 D:210]:
>;
>; Enter the CSR address for this controller. This CSR address can
>; be changed after the SYSGEN by using the VMR CON SET command.
>;
>* CP2472 What is its CSR address? [O R:160000-177700 D:177440]:
>;
>; DM Configuration
>;
>; Physical Unit Number
>;
>; 0 1 2 3 4 5 6 7
>;
>; DMA DM0: DM1: DM2: DM3: DM4: DM5: DM6: DM7:
>;
>;
>;
>;
>; DL: controllers: RL11, RLV12 devices: RL01, RL02
>;
>; The RL11/RLV12 disk subsystem uses a medium performance, RL01/02
>; direct access drive with a single read/write head per surface.
>; Each drive provides 5.2 megabytes (RL01) or 10.4 megabytes (RL02)
>; of storage on a removable, top-loading cartridge. The subsystem
>; is expandable up to four drives.
>;
>* CP2604 How many RL11/RLV11 disk cartridge controllers do
>* you have? [O D:0]: 1
>;
>; Enter the total number of RL01 and RL02 disk drives in your system.
>;
>* CP2608 How many RL01/RL02 disk drives do you have? [D R:1.-63. D:1.]: 4
>;
>;
>; The physical unit number of a drive is the number shown on the
>; unit number plug (or other indicator) on the drive.
>;
>* CP2636 What is the physical unit number of DL0:? [O R:0-7 D:0]:
>;
>; Enter the drive type for this logical unit.
>;
>* CP2660 Is DL0: an RL01 or RL02? [S R:4-4 D:"RL02"]:
>;
>;
>* CP2636 What is the physical unit number of DL1:? [O R:0-7 D:1]:
>;
>* CP2660 Is DL1: an RL01 or RL02? [S R:4-4 D:"RL02"]:
>;
>;
>* CP2636 What is the physical unit number of DL2:? [O R:0-7 D:2]:
>;
>* CP2660 Is DL2: an RL01 or RL02? [S R:4-4 D:"RL02"]:
>;
>;
>* CP2636 What is the physical unit number of DL3:? [O R:0-7 D:3]:
>;
>* CP2660 Is DL3: an RL01 or RL02? [S R:4-4 D:"RL02"]:
>;
>;
>; Enter the vector address for this controller. This vector address
>; can be changed after the SYSGEN by using the VMR CON SET command.
>;
>* CP2668 Enter the vector address of DLA [O R:60-774 D:160]:
>;
>; Enter the CSR address for this controller. This CSR address can
>; be changed after the SYSGEN by using the VMR CON SET command.
>;
>* CP2672 What is its CSR address? [O R:160000-177700 D:174400]:
>;
>; DL Configuration
>;
>; Physical Unit Number
>;
>; 0 1 2 3 4 5 6 7
>;
>; DLA DL0: DL1: DL2: DL3:
>;
>;
>;
>;
>; DP: controller: RP11 devices: RP02, RPR02, RP03
>;
>; The RP11 is a complete mass storage system using a magnetic
>; disk pack with 20 data surfaces and a moving read/write head.
>; The RP02 and RPR02 have a capacity of 20 megabytes. The RP03
>; has a capacity of 41 megabytes.
>;
>* CP2804 How many RP11 disk pack controllers do you have? [O D:0]:
>;
>; DU: controllers: RQZX1, RQDX1, RQDX2, RQDX3,
>; RUX50, RQC25, KDA50, UDA50
>;
>; devices: RX33, RX50, RD31, RD51, RD52, RD53, RD54,
>; RC25, RA60, RA70, RA71, RA72, RA80, RA81,
>; RA82, RA90, RA92, RZ23L, RZ24L, RZ26x, RZ29B
>;
>; The total of DU and MU controllers cannot be greater than 10.
>;
>; The MSCP disk controllers are:
>;
>; RQZX1, RQDX1, RQDX2, RQDX3, RUX50, RQC25, RUC25, KDA50, UDA50
>;
>; These intelligent disk controllers provide enhanced I/O optimization,
>; error correction capability, and, in some cases, dynamic bad block
>; handling.
>;
>* CP3004 How many MSCP disk controllers do you have? [D R:0.-10. D:0.]: 1
>;
>; The MSCP disk drives are:
>;
>; RX33, RX50, RD31, RD51, RD52, RD53, RD54
>; RC25, RA60, RA70, RA71, RA72, RA80, RA81
>; RA82, RA90, RA92, RZ23L, RZ24L, RZ26L
>;
>; The RX33 is a half-height 5.25-inch floppy diskette drive
>; with a formatted capacity of 1.2 megabytes.
>;
>; The RX50 is a full-height dual 5.25 inch floppy diskette drive
>; with a formatted capacity of 400 kilobytes for each diskette.
>; Count each RX50 (with two diskettes) as two drives.
>;
>; The RD31 is a half-height 5.25 inch fixed media, Winchester
>; technology disk with a formatted capacity of 21 megabytes.
>;
>;
>; The RD51 is a 5.25 inch fixed media, Winchester technology disk
>; with a formatted capacity of 10 megabytes.
>;
>; The RD52 is a 5.25 inch fixed media Winchester technology disk
>; with a formatted capacity of 31 megabytes.
>;
>; The RD53 is a 5.25 inch fixed media Winchester technology disk
>; with a formatted capacity of 71 megabytes.
>;
>; The RD54 is a 5.25 inch fixed media Winchester technology disk
>; with a formatted capacity of 159 megabytes.
>;
>; The RC25 contains a fixed and removable disk on the same spindle
>; with a formatted capacity of 25 megabytes each. Count each RC25
>; (with two disks: one fixed, one removable) as two drives.
>;
>; The RA60 is a removable media disk with a formatted capacity of
>; 205 megabytes.
>;
>; The RA70 is a fixed media, Winchester technology disk with a
>; formatted capacity of 280 megabytes.
>;
>; The RA80 is a fixed media, Winchester technology disk with a
>; formatted capacity of 121 megabytes.
>;
>; The RA81 is a fixed media, Winchester technology disk with a
>; formatted capacity of 456 megabytes.
>;
>; The RA82 is a fixed media, Winchester technology disk with a
>; formatted capacity of 622 megabytes.
>;
>; The RA90 is a fixed media, Winchester technology disk with a
>; formatted capacity of 1,216 megabytes.
>;
>; The RZ23L, RZ24L, and RZ26L drives are SCSI disks that attach
>; to the RQZX1 adapter.
>;
>; Enter the total number of physical MSCP disk drives in your system.
>; Do not include any logical partitions in the total.
>;
>* CP3008 How many physical MSCP disk drives do you have? [D D:1.]: 4
>;
>;
>; The physical unit number of a drive is the number shown on the
>; unit number plug (or other indicator) on the drive.
>;
>* CP3036 What is the physical unit number of DU0:? [O R:0-377 D:0]:
>;
>;
>* CP3036 What is the physical unit number of DU1:? [O R:0-377 D:1]:
>;
>;
>* CP3036 What is the physical unit number of DU2:? [O R:0-377 D:2]:
>;
>;
>* CP3036 What is the physical unit number of DU3:? [O R:0-377 D:3]:
>;
>;
>; Enter the vector address for this controller. This vector address
>; can be changed after the SYSGEN by using the VMR CON SET command.
>;
>* CP3068 Enter the vector address of DUA [O R:60-774 D:154]:
>;
>; Enter the CSR address for this controller. This CSR address can
>; be changed after the SYSGEN by using the VMR CON SET command.
>;
>* CP3072 What is its CSR address? [O R:160000-177700 D:172150]:
>;
>;
>; MU: controllers: TK50, TU81, TU81E, TQ81E, RQZX1
>;
>; The TMSCP tape controllers are:
>;
>; TK50, TU81, TU81E, TQ81E, RQZX1
>;
>;
>* CP3404 How many TMSCP tape controllers do you have? [D R:0.-9. D:0.]: 1
>;
>;
>; The physical unit number of a drive is the number shown on the
>; unit number plug (or other indicator) on the drive.
>;
>* CP3436 What is the physical unit number of MU0:? [O R:0-377 D:0]:
>;
>;
>; Enter the vector address for this controller. This vector address
>; can be changed after the SYSGEN by using the VMR CON SET command.
>;
>* CP3468 Enter the vector address of MUA [O R:60-774 D:260]:
>;
>; Enter the CSR address for this controller. This CSR address can
>; be changed after the SYSGEN by using the VMR CON SET command.
>;
>* CP3472 What is its CSR address? [O R:160000-177700 D:174500]:
>;
>; VF: Virtual disk/tape driver
>;
>;
>;
>; CR: controllers: CM11, CR11
>;
>; The CR11 card reader reads EIA standard 80-column punched data
>; cards at 300 cards per minute. It uses a riffle-air and a
>; vacuum-pick mechanism to move the cards. The CM11-F reads 80-
>; column mark-sense cards, which can have punched holes, at 285
>; cards per minute.
>;
>* CP4004 How many CM/CR11 card readers do you have? [O D:0]:
>;
>;
>; CT: controller: TA11 device: TU60
>;
>; The TA11 magnetic tape cassette system is a dual-drive,
>; reel-to-reel unit designed to replace paper tape. Its two
>; drives run non-simultaneously using proprietary Digital
>; Equipment Corporation Philips-type cassettes. The TA11
>; includes a control unit and a dual tape transport.
>;
>* CP4204 How many TA11 dual cassettes do you have? [O D:0]:
>;
>;
>; MS: controllers: TS11, TU80, TSV05, TK25
>;
>; The TS11, TU80, and TSV05 are 1/2 inch 1600 bpi tape subsystems
>; and the TK25 is a cartridge tape subsystem.
>;
>* CP4404 How many TS11/TU80/TSV05/TK25
>* magtape controllers do you have? [O D:0]:
>;
>;
>; DT: controller: TC11 device: TU56
>;
>; The TC11 is a dual-unit bidirectional magnetic-tape transport
>; system for auxiliary data storage.
>;
>; The system stores information at fixed positions on magnetic
>; tape as in magnetic disk or drum storage devices, rather than
>; at unknown or variable positions as in conventional magnetic
>; tape systems.
>;
>; A DECtape system consists of up to 4 dual transports, a control
>; unit (which will buffer and control information for up to four
>; dual transports). A TC11 includes a control unit and the
>; first dual tape transport.
>;
>* CP4604 How many TC11 DECtape controllers do you have? [O D:0]:
>;
>;
>; DX: controller: RX11 device: RX01
>;
>; The RX11 is an industry compatible disk storage system for
>; flexible (floppy) disks. An RX11 is capable of controlling two
>; flexible disk drives each having a capacity of 256K bytes.
>;
>* CP4804 How many RX11 disk controllers do you have? [O D:0]:
>;
>;
>; DY: controller: RX211, RXV21 device: RX02
>;
>; The RX211 and RXV21 are single or double density flexible (floppy) disk
>; controllers with a storage capacity of 256K bytes (single density) or
>; 512K bytes (double density). One controller is capable of controlling
>; two drives.
>;
>* CP5004 How many RX211/RXV21 disk controllers do you have? [O D:0]:
>;
>;
>; DD: controller: DL11 device: TU58
>;
>; The TU58 driver interfaces with the 3M DC-100A tape
>; cartridge drive and controller units via a parallel to ser-
>; ial DL11 converter at baud rates up to 9.6K. Data is
>; stored on the media on two parallel tracks recorded in the
>; same direction. The tape is preformatted into 2048 physical
>; records of 128 bytes each. Access to these physical records
>; is by groups of four corresponding to a standard DEC block
>; of 512 bytes.
>;
>* CP5204 How many TU58 controllers do you have? [O D:0]:
>;
>;
>; LP: controllers: LA180, LN01, LP11, LS11, LV11
>; devices: LA180, LG01, LG02, LN01, LP01, LP02, LP04, LP05,
>; LP06, LP07, LP14, LP25, LP26, LP27, LS11, LV01
>;
>; The LP11 is a high-speed impact line printer with a rotating drum
>; or band. It is available in a variety of models, with and without
>; lowercase characters.
>;
>; The LS11 line printer is a medium-speed impact dot-matrix line
>; printer. It prints at a rate of 165 characters per second at
>; 10 characters per inch with up to 132 characters per line.
>;
>; The LA180 DECprinter is similar to the LS11 with the exception
>; that it prints at the rate of 180 characters per second.
>;
>; The LV11 is a high-speed electrostatic printer-plotter that prints
>; at a rate of 500 lines per minute. Only the print option is
>; supported under RSX-11M-PLUS.
>;
>* CP5404 How many LP/LS/LV/LG/LN/LA180 line printers do you have? [O D:0]: 1
>;
>; If a task tries to access the line printer when the device is not
>; ready, a message saying the line printer is not ready is printed
>; on the console terminal. This message is repeated every n seconds,
>; where n is your response to this question, for as long as the line
>; printer remains not ready.
>;
>; Enter zero to disable this feature and suppress the messages.
>;
>* CP5408 Enter the number of seconds between
>* line printer-not-ready messages [D R:0.-255. D:15.]: 30
>;
>; Enter the vector address for this line printer. This vector address
>; can be changed after the SYSGEN by using the VMR CON SET command.
>;
>* CP5468 Enter vector address of the next line
>* printer [O R:60-774 D:200]:
>;
>; Enter the CSR address for this line printer. This CSR address can
>; be changed after the SYSGEN by using the VMR CON SET command.
>;
>* CP5472 What is its CSR address? [O R:160000-177700 D:177514]:
>;
>; Here is a table of the valid line printer types and their
>; characteristics:
>;
>; printer # of lines per supports
>; type controller columns minute optimization
>;
>; LA180 LA180 132 150 no
>; LG01 LP11 132 240-600 no
>; LG02 LP11 132 240-600 no
>; LN01 LN01 132 600 NA
>; LP01 LP11-F/H 80 170-1110 yes
>; LP02 LP11-J/K 132 170-1110 yes
>; LP04 LP11-R/S 132 1110 yes
>; LP05 LP11-V/W 132 300 no
>; LP06 LP11-Y/Z 132 460-600 no
>; LP07 LP11-G 132 1200 no
>; LP14 LP11-C/D 132 660-900 no
>; LP25 LP11-A/B 132 215-300 no
>; LP26 LP11-E 132 445-600 no
>; LP27 LP11-U 132 800-1200 no
>; LS11 LS11 132 60-200 no
>; LV01 LV11 132 500 yes
>;
>; The printer type is used to set two characteristics in the UCB:
>;
>; o Column or buffer width
>;
>; This is settable in VMR or MCR with the SET /BUF command.
>;
>;
>; o Fast line printer support
>;
>; This is an optimization performed by the driver to eliminate
>; unnecessary print cycles. This characteristic is not settable
>; in VMR or MCR.
>;
>; If you specify the wrong printer type and the driver performs
>; the optimization for a printer that does not support it, you
>; will occasionally lose a line of a listing when the printer
>; is taken off line.
>;
>; If you specify the wrong printer type and the driver does not
>; perform the optimization for a printer that supports it, the
>; printer will run a little slower than it would with the
>; optimization, but there will be no other adverse effects.
>;
>; If you do not know the correct printer type for your printer, take
>; the default. This will give you a 132-column printer without fast
>; printer optimization. Once your system is running, you can change
>; the number of columns if necessary with the MCR SET command.
>;
>* CP5480 Enter line printer type for LPA [S R:4-5 D:"LP25"]:
>;
>; If this line printer has both uppercase and lowercase characters,
>; answer Yes to this question. If it only has uppercase characters,
>; answer No. Your answer determines the initial setting for
>; lowercase character conversion on this printer. You can change
>; this at any time by using the MCR SET /LOWER command.
>;
>* CP5484 Does LPA have lowercase characters? [Y/N D:N]:
>;
>;
>; MT: controllers: TM11, TMA11, TMB11 devices: TE10, TU10, TU10W, TS03
>;
>; The TM/TMA/TMB11 is a magnetic tape system ideally suited for
>; writing, reading, and storing large volumes of data and
>; programs in a serial manner. The system reads and writes in
>; industry-compatible format. TU10 drives support 10.5-inch reels
>; containing up to 2400 feet of tape upon which over 180 million
>; bits of data can be stored on high density 9-track tape. TS03
>; drives support 7-inch reels containing up to 600 feet of tape in
>; high density 9-track format. TU10W drives are compatible with
>; TU10 drives except they operate only on 800 bpi, 9-track tape.
>;
>* CP5604 How many TM/TMA/TMB11 magtape controllers do you have? [O D:0]:
>;
>;
>; PP: controller: PC11
>;
>; The PC11 is a high speed paper tape reader/punch that is
>; capable of reading eight-hole, unoiled, perforated paper tape at
>; 300 characters per second, and punching tape at 50 characters
>; per second.
>;
>* CP5804 How many PC11 paper tape reader/punches do you have? [O D:0]:
>;
>;
>; PR: controller: PR11
>;
>; The PR11 is a high speed paper tape reader that is capable of
>; reading eight-hole unoiled perforated paper tape at 300
>; characters per second.
>;
>;
>* CP6004 How many PR11 paper tape readers do you have? [O D:0]:
>;
>;
>; LA: controller: LPA11
>;
>; The LPA11 lab peripheral accelerator is a real-time subsystem which
>; interfaces to the PDP-11 family of computers. The system consists
>; of the LPA11, up to 2 A/D converters, a programmable real-time
>; clock, a D/A converter, and up to five digital I/O modules.
>;
>* CP6204 How many LPA11 lab subsystems do you have? [D R:0.-16. D:0.]:
>;
>;
>; TT: controllers: DL11, DLV11 controller mnemonic: YL
>;
>; The DL11/DLV11 series of asynchronous single line interfaces handle
>; full or half-duplex communication between a wide variety of serial
>; communication channels and a PDP-11 computer.
>;
>; SYSGEN automatically sets up the data bases for all mandatory
>; DL11/DLV11s. (For each processor in the system, there must be a
>; DL11/DLV11; these are mandatory.) Answer the next question with
>; the number of additional DL11/DLV11s in your system.
>;
>; Note: Enter only the number of DL11s used as terminal interfaces.
>; Do not include any DL11s used as controlers for the TU58 DECtape II.
>;
>* CP6804 Enter number of additional DL11/DLV11 line interfaces [O D:0]:
>;
>; The terminal types supported by RSX-11M-PLUS SYSGEN are:
>;
>; ASR33 LA12 VT05B
>; ASR35 LA30P VT50
>; LA30S VT52
>; DTC01 LA34 VT55
>; LA36 VT61
>; KSR33 LA38 VT100
>; LA50 VT101
>; LA100 VT102
>; LA120 VT105
>; LA180S VT125
>; LA210 VT131
>; LN03 VT132
>; PC3xx VT2xx
>;
>* CP6832 Enter terminal type for YLA [S R:4-6 D:"LA120"]: VT2XX
>;
>;
>; TT: controller: DH11 controller mnemonic: YH
>;
>; The DH11 multiplexer connects the PDP-11 with 16 asynchronous
>; serial communications lines operating with individually
>; programmable parameters. These parameters are:
>;
>; transmitter speed (baud)
>; receiver speed (baud)
>;
>* CP7004 Enter number of DH11 asynchronous line
>* multiplexers [D R:0.-16. D:0.]:
>;
>;
>; TT: controller mnemonic: YV
>;
>; controllers: DHU11, DHV11, CXA16, CXB16, CXY08
>;
>;
>; These multiplexers connect the PDP-11 with up to
>; 16 (DHU11, CXA16, CXB16) or 8 (DHV11, CXY08)
>; asynchronous serial communications lines operating with
>; individually programmable parameters. These parameters are:
>;
>; transmitter speed (baud)
>; receiver speed (baud)
>;
>; Modem control is available with the DHU11, DHV11 and CXY08.
>; The CXA16 and CXB16 do not support modem control. Use the VMR
>; or MCR SET /REMOTE commands in order to enable dialup lines.
>;
>* CP7104 Enter number of DHU11/DHV11/CXA16/CXB16/CXY08 (YV:-type)
>* asynchronous line multiplexers [D R:0.-32. D:0.]:
>;
>;
>; TT: controller: DJ11 controller mnemonic: YJ
>;
>; The DJ11 is a multiplexed interface between 16 asynchronous
>; serial data-communications channels and the PDP-11 UNIBUS. The
>; DJ11 is a unit whose character formats and operating speeds are
>; jumper or strap selectable in groups of four lines.
>;
>* CP7204 Enter number of DJ11 asynchronous line
>* multiplexers [D R:0.-16. D:0.]:
>;
>;
>; TT: controllers: DZ11, DZQ11, DZV11, DFA01 controller mnemonic: YZ
>;
>; The DZ11/DZQ11/DZV11/DFA01 multiplexers connect the PDP-11 with up to
>; 8 asynchronous serial communications lines operating with individually
>; programmable parameters. These parameters are:
>;
>; Transmitter speed / Receiver speed (baud)
>;
>* CP7404 Enter number of DZ11/DZQ11/DZV11/DFA01 asynchronous line
>* multiplexers [D R:0.-32. D:0.]: 4
>;
>; The DZ11/DZQ11/DZV11 has the ability to maintain a full-duplex connection
>; through a BELL 103A type modem. Modem support requires added code in the
>; terminal driver and increases system overhead. As a result, it should be
>; selected only if needed.
>;
>* CP7420 Do any of the DZ lines require modem support? [Y/N D:N]: Y
>;
>; The valid baud rates are:
>;
>; 50
>; 75
>; 110
>; 134.5
>; 150
>; 300
>; 600
>; 1200
>; 1800
>; 2000
>; 2400
>; 3600
>; 4800
>; 7200
>; 9600
>;
>* CP7428 At which baud rate do you want to answer? [S R:2-5 D:"300"]: 9600
>;
>; The vector address for the DZ11/DZQ11/DZV11 is assigned from the floating
>; vector space starting at 300. The vector address can be changed after
>; the SYSGEN by using the VMR CON SET command.
>;
>* CP7468 Enter vector address of YZA [O R:300-770]: 300
>;
>; The CSR address for the DZ11/DZQ11/DZV11 is assigned from the floating
>; address space starting at 160010. The CSR address can be changed
>; after the SYSGEN by using the VMR CON SET command.
>;
>* CP7472 What is its CSR address? [O R:160000-177700]: 160100
>;
>; Enter the number of lines on this controller.
>;
>* CP7480 How many lines does YZA have? [D R:1.-8. D:8.]:
>;
>; The terminal types supported by RSX-11M-PLUS SYSGEN are:
>;
>; ASR33 LA12 VT05B
>; ASR35 LA30P VT50
>; LA30S VT52
>; DTC01 LA34 VT55
>; LA36 VT61
>; KSR33 LA38 VT100
>; LA50 VT101
>; LA100 VT102
>; LA120 VT105
>; LA180S VT125
>; LA210 VT131
>; LN03 VT132
>; PC3xx VT2xx
>;
>* CP7484 Enter terminal type for YZA [S R:4-6 D:"VT100"]:
>;
>; The vector address for the DZ11/DZQ11/DZV11 is assigned from the floating
>; vector space starting at 300. The vector address can be changed after
>; the SYSGEN by using the VMR CON SET command.
>;
>* CP7468 Enter vector address of YZB [O R:300-770]: 310
>;
>* CP7472 What is its CSR address? [O R:160000-177700]: 160110
>;
>; Enter the number of lines on this controller.
>;
>* CP7480 How many lines does YZB have? [D R:1.-8. D:8.]:
>;
>; The terminal types supported by RSX-11M-PLUS SYSGEN are:
>;
>; ASR33 LA12 VT05B
>; ASR35 LA30P VT50
>; LA30S VT52
>; DTC01 LA34 VT55
>; LA36 VT61
>; KSR33 LA38 VT100
>; LA50 VT101
>; LA100 VT102
>; LA120 VT105
>; LA180S VT125
>; LA210 VT131
>; LN03 VT132
>; PC3xx VT2xx
>;
>* CP7484 Enter terminal type for YZB [S R:4-6 D:"VT100"]:
>;
>; The vector address for the DZ11/DZQ11/DZV11 is assigned from the floating
>; vector space starting at 300. The vector address can be changed after
>; the SYSGEN by using the VMR CON SET command.
>;
>* CP7468 Enter vector address of YZC [O R:300-770]: 320
>;
>* CP7472 What is its CSR address? [O R:160000-177700]: 160120
>;
>; Enter the number of lines on this controller.
>;
>* CP7480 How many lines does YZC have? [D R:1.-8. D:8.]:
>;
>; The terminal types supported by RSX-11M-PLUS SYSGEN are:
>;
>; ASR33 LA12 VT05B
>; ASR35 LA30P VT50
>; LA30S VT52
>; DTC01 LA34 VT55
>; LA36 VT61
>; KSR33 LA38 VT100
>; LA50 VT101
>; LA100 VT102
>; LA120 VT105
>; LA180S VT125
>; LA210 VT131
>; LN03 VT132
>; PC3xx VT2xx
>;
>* CP7484 Enter terminal type for YZC [S R:4-6 D:"VT100"]:
>;
>; The vector address for the DZ11/DZQ11/DZV11 is assigned from the floating
>; vector space starting at 300. The vector address can be changed after
>; the SYSGEN by using the VMR CON SET command.
>;
>* CP7468 Enter vector address of YZD [O R:300-770]: 330
>;
>* CP7472 What is its CSR address? [O R:160000-177700]: 160130
>;
>; Enter the number of lines on this controller.
>;
>* CP7480 How many lines does YZD have? [D R:1.-8. D:8.]:
>;
>; The terminal types supported by RSX-11M-PLUS SYSGEN are:
>;
>; ASR33 LA12 VT05B
>; ASR35 LA30P VT50
>; LA30S VT52
>; DTC01 LA34 VT55
>; LA36 VT61
>; KSR33 LA38 VT100
>; LA50 VT101
>; LA100 VT102
>; LA120 VT105
>; LA180S VT125
>; LA210 VT131
>; LN03 VT132
>; PC3xx VT2xx
>;
>* CP7484 Enter terminal type for YZD [S R:4-6 D:"VT100"]:
>;
>; SYSVMR.CMD, the VMR command file which creates your system image file,
>; contains commands that set the characteristics for each terminal as
>; follows:
>;
>; Terminal type: as you specified for the controller
>; Buffer width: 80
>; Speed: 300/300 for hardcopy terminals
>; 9600/9600 for CRTs
>; Lower to upper-
>; case conversion: No for hardcopy terminals
>; Yes for CRTs
>;
>; If you wish to change these characteristics for your terminals, SYSGEN
>; will allow you to edit SYSVMR.CMD.
>;
>;
>;
>; Intercomputer communication devices consist of the following:
>;
>; PCL11 full-duplex DMA interprocessor communications
>; device
>; DMC11/DMR11 high-speed synchronous serial line interface
>; DUP11 synchronous serial line interface
>; DEUNA Ethernet communications controller
>;
>; Note: Do NOT include any devices which will be used with DECnet.
>; Those devices should be included when you do your NETGEN.
>;
>* CP7604 Do you have any intercomputer communication devices? [Y/N D:N]:
>;
>;
>; Enter device mnemonics for any user-supplied drivers. The driver
>; source files must reside in [11,10] and be named ddDRV.MAC and
>; ddTAB.MAC where dd is the device mnemonic.
>;
>; You may enter the mnemonics on more than one line. When you have
>; listed all the drivers, press RETURN when asked for the device
>; mnemonic.
>;
>; The device mnemonic must not include a colon.
>;
>* CP9604 Enter device mnemonics for user-supplied drivers [S]:
>;
>;
>; If you will be adding other devices after this SYSGEN or have
>; included user-supplied devices, you will want to set the highest
>; interrupt vector address high enough to accommodate the vectors for
>; those devices.
>;
>; The highest vector among the devices you specified in this SYSGEN
>; is 374(octal). This is the default response for this question.
>;
>* CP9632 What is the highest interrupt vector
>* address? [O R:374-774 D:374]: 774
>;
>;
>;
>;================================================================
>; Assembling the Executive and Drivers 19-OCT-08 at 15:47
>;================================================================
>;
>;
>;
>; The answers to the questions in this section are put in the saved
>; answer file [200,200]SYSGENSA1.CMD.
>;
>PIP RSXMC3.MAC=RSXMC1.MAC,RSXMC2.MAC
>PIP RSXMC.MAC=RSXMC3.MAC,RSXMC0.MAC
>;
>; Copy the files created by the Executive options and peripheral
>; configuration sections into the correct directories.
>;
>SET /UIC=[1,24]
>PIP [11,10]/NV=[200,200]RSXMC.MAC
>PIP [11,10]/NV=[200,200]SYSTB.MAC
>PIP [11,24]/NV=[200,200]RSXASM.CMD
>PIP [11,24]/NV=[200,200]DRIVERS.ASM
>;
>;
>; Assembly listings of the Executive modules and the drivers can be
>; generated and stored in a file or printed directly.
>;
>; Generating listings is time-consuming and they are not normally
>; needed, so we recommend you answer No to this question.
>;
>* AE010 Do you want assembly listings of the Executive and
>* drivers? [Y/N D:N]: Y
>;
>; Listings can be sent directly to a printer or can be stored
>; on a directory device for printing later. If you enter a
>; directory device, the listings will be put in UFD [11,34].
>;
>* AE020 What is to be the listing device [ddu:]? [S R:2-5 D:"SY:"]:
>;
>ASN SY:=LS:
>;
>;
>; If you are building a specialized system you may wish to edit
>; some of the files which SYSGEN produced before the Executive
>; and drivers are assembled.
>;
>* AE030 Do you wish to pause to edit any files before
>* assembling? [Y/N D:N]:
>;
>SET /UIC=[11,24]
>;
>; Now we assemble the Executive and resident drivers.
>;
>PIP *.OBJ;*/DE/NM,*.TTY;*
>;
>TIME
15:48:04 19-OCT-08
>;
>MAC @RSXASM
>;
>; Now we assemble the loadable drivers.
>;
>TIME
15:49:43 19-OCT-08
>;
>MAC @DRIVERS.ASM
>;
>TIME
15:51:02 19-OCT-08
>;
>; Now we build the concatenated object module file for the Executive.
>;
>PIP RSX11M.OBS=*.OBJ
>PIP TTDRV.OBS=*.TTY
>;
>SET /UIC=[200,200]
>PIP /NV=[11,10]RSXMC.MAC
>;
>SET /UIC=[1,24]
>PIP RSXBLD.CMD/PU/NM
>PIP RSX11M.OLB;*/DE/NM
>PIP [200,200]RSXMC.MAC/PU/NM
>;
>; Now we build the Executive library.
>;
>LBR RSX11M/CR:256.::256./-EP=[11,24]RSX11M.OBS
>PIP [11,24]RSX11M.OBS;*,*.OBJ;*/DE
>;
>; Now we build the terminal driver library.
>;
>LBR TTDRV/CR:40.:392.:128.=[11,24]TTDRV.OBS
>PIP [11,24]TTDRV.OBS;*,*.TTY;*/DE
>SET /UIC=[200,200]
>;
>;
>;
>;==============================================================
>; Building the Executive and Drivers 19-OCT-08 at 15:51
>;==============================================================
>;
>;
>;
>; The answers to the questions in this section are put in the saved
>; answer file [200,200]SYSGENSA1.CMD.
>;
>;
>; There is a system image file, RSX11M.SYS, in UFD [1,54] on your
>; target system disk. This is probably an old system. You may want
>; to move the files belonging to this older system to another directory
>; before SYSGEN puts the new system's files in [1,54].
>;
>* BE010 Do you want to move the old system in [1,54] to
>* another directory? [Y/N D:N]:
>;
>; Allocate space to be used later for the system image file.
>;
>SET /UIC=[1,54]
>PIP RSX11M.TMP/CO/BL:1026.=NL:
>;
>SET /UIC=[200,200]
>;
>SET /UIC=[1,24]
>SET /UIC=[200,200]
>SET /UIC=[1,54]
>PIP SYSVMR.CMD=[200,200]SYSVMR.CMD,VMRTTY.CMD
>;
>SET /UIC=[200,200]
>;
>; At this point, you can edit:
>;
>; the Executive task-build command files in [200,200]
>; the driver task-build command files in [200,200]
>; the privileged task task-build command files in [1,24]
>; SYSVMR.CMD in [1,54]
>;
>; In most cases there is no need to edit the task-build command files.
>; However, you may want to tailor SYSVMR for your system.
>;
>* BE030 Do you want to pause to edit any files before
>* task-building? [Y/N D:N]:
>;
>SET /UIC=[1,24]
>PIP [1,24]/NV/NM=[200,200]RSXBLD.CMD,RSX11M,DSP11M,LDR11M
>PIP [1,24]/NV=[200,200]DIR11M.CMD,DR211M,DIRCOM,DR2COM,DIR
>PIP [1,24]/NV=[200,200]DR311M.CMD,DR411M,DR3COM,DR4COM
>PIP [1,24]/NV=[200,200]VEC11M.CMD,DCM11M,VECCOM
>;
>; Now we build the Executive.
>;
>TIME
15:51:12 19-OCT-08
>;
>TKB @RSXBLD
>;
>; Now we build the loadable drivers
>;
>TIME
15:51:31 19-OCT-08
>;
>TKB @[200,200]DRIVERS.BLD
>;
>TIME
15:51:36 19-OCT-08
>SET /UIC=[200,200]
>;
>;
>;
>;=========================================================
>; Building the Privileged Task 19-OCT-08 at 15:51
>;=========================================================
>;
>;
>;
>; The answers to the questions in this section are put in the saved
>; answer file [200,200]SYSGENSA1.CMD.
>;
>;
>; Maps of the privileged tasks can be generated and stored in a file
>; or printed directly.
>;
>; Maps of the privileged tasks are not normally needed, so we
>; recommend you answer No to this question.
>;
>* BP040 Do you want the maps of the privileged tasks? [Y/N D:N]: Y
>;
>; The maps can be sent directly to a printer or can be stored
>; on a directory device for printing later. If you enter a
>; directory device, the maps will be put in UFD [1,34].
>;
>* BP050 What is to be the map device [ddu:]? [S R:2-5 D:"SY:"]:
>;
>ASN SY:=MP:
>;
>SET /UIC=[1,24]
>;
>TIME
15:51:40 19-OCT-08
>;
>TKB @SAVBLD
>;
>TIME
15:51:45 19-OCT-08
>;
>ASN LB:=OU:
>SET /UIC=[200,200]
>;
>;
>;
>;============================================================
>; Rebuilding Supplied System Tasks 19-OCT-08 at 15:51
>;============================================================
>;
>;
>;
>; The answers to the questions in this section are put in the saved
>; answer file [200,200]SYSGENSA3.CMD.
>;
>;
>; All nonprivileged and vectored privileged system tasks are supplied
>; already task-built and can be found in the library UFD on the target
>; system disk. It is not normally necessary to rebuild these supplied
>; system tasks although you may wish to do so, for example if one of
>; them has been patched.
>;
>* BN010 Do you want to rebuild any system tasks? [Y/N D:N]:
>;
>;
>;
>;==========================================================
>; Creating the System Image File 19-OCT-08 at 15:51
>;==========================================================
>;
>;
>SET /UIC=[1,54]
>;
>PIP RSX11M.TMP;*/DE/NM
>;
>PIP RSX11M.SYS/CO/NV/BL:1026.=RSX11M.TSK
>;
>ASN LB:=SY:
>;
>; Utility tasks stay in utility UFD [3,54].
>;
>; RSX11M.TSK is a backup copy of the Executive you just built.
>;
>;
>; VMR will now initialize the system.
>;
>VMR @SYSVMR
Loading Executive data space
Data space loading completed
VMR -- *DIAG*-Installed tasks or commons may no longer fit in partition
SET /TOP=SYSPAR:-*
VMR -- *DIAG*-Loadable driver larger than 4K
LOA TT:
VMR -- *DIAG*-Installed tasks or commons may no longer fit in partition
SET /TOP=DRVPAR:-*
SECPOL 117734 00202000 00100000 SEC POOL
SYSPAR 117670 00302000 00205600 MAIN
117624 00302000 00115300 RO COM !DIR11M!
117434 00417300 00005200 TASK [...LDR]
117230 00424500 00033500 TASK [MCR...]
117024 00460200 00010500 TASK [TKTN ]
116620 00470700 00003200 TASK [SHF...]
116414 00474100 00013500 TASK [RCT...]
DRVPAR 116334 00507600 00170400 MAIN
116270 00507600 00006600 RO COM !TTEXT !
116204 00516400 00020600 RO COM !TTCOM !
116120 00537200 00035000 DRIVER (TT:)
114674 00574200 00005000 DRIVER (DB:)
114404 00601200 00005300 DRIVER (MM:)
113160 00606500 00005200 DRIVER (DM:)
112360 00613700 00003500 DRIVER (DL:)
112314 00617400 00005100 RO COM !PUCOM !
111514 00624500 00014000 DRIVER (DU:)
111160 00640500 00011500 DRIVER (MU:)
110740 00652200 00001300 DRIVER (LP:)
110550 00653500 00000100 DRIVER (NL:)
110504 00653600 00017700 DRIVER (VF:)
110440 00673500 00000300 DRIVER (CO:)
110374 00674000 00002500 DRIVER (VT:)
110330 00676500 00001500 DRIVER (RD:)
GEN 110264 00700200 01077600 MAIN
...LDR 12.01 117500 SYSPAR 248. 00005200 LB0:-00055223 FIXED
TKTN 07.01 117070 SYSPAR 248. 00010500 LB0:-00114673 FIXED
F11MSG 15.00 106204 GEN 200. 00006300 LB0:-00103162
MTAACP 17.00 105610 GEN 200. 00016200 LB0:-00107642
SHE... 06.01 105340 GEN 200. 00014500 LB0:-00113311
MCR... 07.00 117274 SYSPAR 160. 00033500 LB0:-00106621 FIXED
F11ACP 07.00D 110050 GEN 149. 00041000 LB0:-00101702
ERRLOG 05.03 107510 GEN 148. 00056200 LB0:-00101550
PMT... 02.02 107050 GEN 148. 00007500 LB0:-00110552
COT... 02.04 106330 GEN 145. 00014300 LB0:-00076006
HRC... 05.00 105734 GEN 140. 00042500 LB0:-00103746
PMD... 07.05 105464 GEN 140. 00017600 LB0:-00110522
SYSLOG 04.03 106600 GEN 130. 00024500 LB0:-00113551
SHF... 07.01 116664 SYSPAR 105. 00003200 LB0:-00113330 FIXED
RCT... 06.02 116460 SYSPAR 100. 00013500 LB0:-00111215 FIXED
FXR... 03.02 106060 GEN 100. 00003300 LB0:-00103154
BAP0 04.11 107634 GEN 80. 00050300 LB0:-00073465
QMG... 06.04 106724 GEN 75. 00037300 LB0:-00111154
LP0 07.04 107270 GEN 70. 00020300 LB0:-00106137
ACNT 06.04 106454 GEN 50. 00057100 LB0:-00073053
SHUTUP 04.04 105214 GEN 50. 00016500 LB0:-00113335
...RMD 05.00 002056+ GEN 225. 00042000 LB0:-00111237
...DCL 06.01 002032+ GEN 160. 00062500 LB0:-00076312
...DMO 04.02 002034+ GEN 160. 00017300 LB0:-00077265
...MCR 07.00 002050+ GEN 160. 00040300 LB0:-00106657
...MOU 26.06 002052+ GEN 160. 00045600 LB0:-00107551
...CA. 01.00 002106+ GEN 150. 00026100 LB0:-00113600
...INS 16.00 002046+ GEN 100. 00053200 LB0:-00104633
...SAV 11.00 002102+ GEN 100. 00070500 LB0:-00061067
...UFD 07.02 002110+ GEN 100. 00014500 LB0:-00114706
...VCP V04.10 002112+ GEN 90. 00020300 LB0:-00115074
...ACS 04.00 002064+ GEN 70. 00006200 LB0:-00073306
...ACC 05.00 002024+ GEN 65. 00032100 LB0:-00072614
...SHA 06.01 002104+ GEN 65. 00032000 LB0:-00113136
...AT. 10.0 002040+ GEN 64. 00056500 LB0:-00104217
...INI 24.00 002042+ GEN 60. 00037200 LB0:-00104537
...HOM 24.00 002044+ GEN 60. 00037200 LB0:-00104537
...BRO 09.10 002026+ GEN 50. 00041500 LB0:-00073613
...BYE 05.01 002030+ GEN 50. 00021700 LB0:-00074117
...HEL 06.00 002036+ GEN 50. 00031600 LB0:-00103312
...PIP 21.00 002054+ GEN 50. 00027500 LB0:-00110247
...UNL 05.04 002060+ GEN 50. 00021500 LB0:-00115022
...ACD 03.00 002062+ GEN 50. 00042500 LB0:-00072705
...BOO 03.10 002066+ GEN 50. 00047200 LB0:-00073413
...CON 05.00 002070+ GEN 50. 00135600 LB0:-00075604
...ELI 04.03 002072+ GEN 50. 00032600 LB0:-00101513
...LOA 05.03 002074+ GEN 50. 00040000 LB0:-00105742
...MAG 03.00 002076+ GEN 50. 00037300 LB0:-00106557
...PSW 03.02 002100+ GEN 50. 00017500 LB0:-00110637
RHA OFL CPA CSR=176700 VEC=254 PRI=5
RHC OFL CPA CSR=172440 VEC=224 PRI=5
DMA OFL CPA CSR=177440 VEC=210 PRI=5
YLA OFL CPA CSR=177560 VEC=60 PRI=5
YZA OFL CPA CSR=160100 VEC=300 PRI=5
YZB OFL CPA CSR=160110 VEC=310 PRI=5
YZC OFL CPA CSR=160120 VEC=320 PRI=5
YZD OFL CPA CSR=160130 VEC=330 PRI=5
DLA OFL CPA CSR=174400 VEC=160 PRI=5
DUA OFL CPA CSR=172150 VEC=154 PRI=5
MUA OFL CPA CSR=174500 VEC=260 PRI=5
LPA OFL CPA CSR=177514 VEC=200 PRI=4
VF0: OFL DRIVER
CO0: OFL DRIVER
TT0: YLA0: OFL DRIVER
TT1: YZA0: OFL DRIVER
TT2: YZA1: OFL DRIVER
TT3: YZA2: OFL DRIVER
TT4: YZA3: OFL DRIVER
TT5: YZA4: OFL DRIVER
TT6: YZA5: OFL DRIVER
TT7: YZA6: OFL DRIVER
TT10: YZA7: OFL DRIVER
TT11: YZB0: OFL DRIVER
TT12: YZB1: OFL DRIVER
TT13: YZB2: OFL DRIVER
TT14: YZB3: OFL DRIVER
TT15: YZB4: OFL DRIVER
TT16: YZB5: OFL DRIVER
TT17: YZB6: OFL DRIVER
TT20: YZB7: OFL DRIVER
TT21: YZC0: OFL DRIVER
TT22: YZC1: OFL DRIVER
TT23: YZC2: OFL DRIVER
TT24: YZC3: OFL DRIVER
TT25: YZC4: OFL DRIVER
TT26: YZC5: OFL DRIVER
TT27: YZC6: OFL DRIVER
TT30: YZC7: OFL DRIVER
TT31: YZD0: OFL DRIVER
TT32: YZD1: OFL DRIVER
TT33: YZD2: OFL DRIVER
TT34: YZD3: OFL DRIVER
TT35: YZD4: OFL DRIVER
TT36: YZD5: OFL DRIVER
TT37: YZD6: OFL DRIVER
TT40: YZD7: OFL DRIVER
VT0: OFL DRIVER
RD0: ONL DRIVER
DB0: RHA0: OFL DRIVER
DB1: RHA1: OFL DRIVER
DB2: RHA2: OFL DRIVER
DB3: RHA3: OFL DRIVER
DB4: RHA4: OFL DRIVER
DB5: RHA5: OFL DRIVER
DB6: RHA6: OFL DRIVER
DB7: RHA7: OFL DRIVER
MM0: RHC0: OFL DRIVER
DM0: DMA0: OFL DRIVER
DM1: DMA1: OFL DRIVER
DM2: DMA2: OFL DRIVER
DM3: DMA3: OFL DRIVER
DM4: DMA4: OFL DRIVER
DM5: DMA5: OFL DRIVER
DM6: DMA6: OFL DRIVER
DM7: DMA7: OFL DRIVER
DL0: DLA0: OFL DRIVER
DL1: DLA1: OFL DRIVER
DL2: DLA2: OFL DRIVER
DL3: DLA3: OFL DRIVER
DU0: DUA0: OFL DRIVER
DU1: DUA1: OFL DRIVER
DU2: DUA2: OFL DRIVER
DU3: DUA3: OFL DRIVER
MU0: MUA0: OFL DRIVER
LP0: LPA0: OFL DRIVER
NL0: OFL DRIVER
POOL=1200:11580.:11580.:2020
>;
>; When you are finished with SYSGEN, software boot in your target
>; system. Set the date and time, and save the system without any
>; switches to verify that the system is working. Then save the
>; system again, this time with the /WB switch to make it hardware
>; bootable.
>;
>; The optional SAVE switches are:
>;
>; /WB writes the boot block
>; /SFILE="filename" uses "filename" as the startup file
>; /MOU="mount-switches" specifies mount switches to be used
>; when the system volume is mounted
>;
>; For example:
>;
>; >BOOT [1,54]RSX11M.SYS
>; XDT: 24
>;
>; XDT>G
>; RSX-11M-PLUS V3.0 BL24
>;
>; >
>; TIM 19-APR-85 12:00:00
>; >SAV
>;
>; RSX-11M-PLUS V3.0 BL24 256.K System:"MJTOAD"
>; >RED DB:=SY:
>; >RED DB:=LB:
>; >RED DB:=SP:
>; >MOU DB:"RSX11MPBL24"
>; >@DB:[1,2]STARTUP
>; .
>; .
>; .
>; >* Please enter time and date (HH:MM MM/DD/YY) [S]: ^Z
>; >@ <EOF>
>; >SAV /WB
>;
>; RSX-11M-PLUS V3.0 BL24 256.K System:"MJTOAD"
>; >RED DB:=SY:
>; >RED DB:=LB:
>; >RED DB:=SP:
>; >MOU DB:"RSX11MPBL24"
>; >@DB:[1,2]STARTUP
>; .
>; .
>; .
>; >* Please enter time and date (HH:MM MM/DD/YY) [S]: 12:01 4/19/85
>; >TIME 12:01 4/19/85
>; >ACS SY:/BLKS=1024.
>; >CON ONLINE ALL
>; .
>; .
>; .
>; >@ <EOF>
>; >SET /UIC=[1,54]
>; >PIP [2,54]*.*;*/DE
>; >
>;
>; You may wish to edit [1,2]STARTUP.CMD and [1,2]QMGSTART.CMD
>; to reflect your desired initialization operations.
>;
>SET /UIC=[200,200]
>;
>REM MACT0
>REM PIPT0
>REM LBRT0
>REM TKBT0
>REM VMRT0
>;
>; End of SYSGEN
>;
>TIME
15:51:51 19-OCT-08
>;
>ASN =
>;
>@ <EOF>
>BOO [1,54]
XDT: 87
XDT>G
RSX-11M-PLUS V4.6 BL87
>
>SAV /WB
RSX-11M-PLUS V4.6 BL87 512.KW System:"BOPOHA"
>RED DU:=SY:
>RED DU:=LB:
>RED DU:=SP:
>MOU DU0:"RSX11MPBL87"
>@DU:[1,2]STARTUP
>;
>; Curent time and date is 15:52:13 19-OCT-2008
>;
>* Please enter time and date (HH:MM DD-MMM-YYYY) [S T:10S]: